Make a donation

Author Topic: MDI + 7p6 Loom  (Read 2442 times)

Offline shoaybmakda

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 25
  • -Receive: 54
  • Posts: 1227
MDI + 7p6 Loom
« on: July 03, 2017, 12:44:51 am »
hi

hope someone can answer this question.

is there a different loom people use for installing an MDI kit and 7p6 bluetooth module? my sound quality on the MDI has dropped since installing the 7p6 module and wasn't sure if a completely different loom is required.

any help is much appreciated

Offline shoaybmakda

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 25
  • -Receive: 54
  • Posts: 1227
Re: MDI + 7p6 Loom
« Reply #1 on: July 19, 2017, 10:24:03 am »
Bump

Offline shoaybmakda

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 25
  • -Receive: 54
  • Posts: 1227
Re: MDI + 7p6 Loom
« Reply #2 on: July 27, 2017, 07:44:55 am »
Anyone?

Or can anyone advise if they have MDI and 7p6 Bluetooth fitted and had any issues?

Offline SI-R32

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 8
  • -Receive: 125
  • Posts: 1001
Re: MDI + 7p6 Loom
« Reply #3 on: July 27, 2017, 09:10:23 am »
What stereo is it going into.

Most vw stereos have different inputs for Bluetooth and MDI, I take it when you've added BT you've piggybacked another loom in via quad lock to quad lock?

Was the MDI already in the car when you got it?
Loads of extra's and retro fits.

Offline shoaybmakda

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 25
  • -Receive: 54
  • Posts: 1227
Re: MDI + 7p6 Loom
« Reply #4 on: July 28, 2017, 12:17:28 am »
@SI-R32 its going into an RNS510 if that helps.

i didnt have any of this installed from scratch - i fitted the unit and mdi myself using an MDI loom then had the bluetooth retrofitted with a 7p6 loom so both looms connected in if that makes sense?

Offline Pashka

  • Won't Shut up.
  • *****
  • Thank You
  • -Given: 4
  • -Receive: 33
  • Posts: 624
    • Email
Re: MDI + 7p6 Loom
« Reply #5 on: July 28, 2017, 06:58:47 am »
Check MDI wires for the speakers if they are not broken. Also, it should be shielded wires for sound signal. And if you use 2 inline looms, i would cut one and solder to each other. Positive, ground, can high, can low. I had similar issue when added aux leads to MDI loom, thin wires got scratched/damaged during the fitting and making the noisy sound.
I have bluetooth, mdi, aux fitted, just no inline looms, everything soldered to the main quad lock. 
« Last Edit: July 28, 2017, 07:03:49 am by Pashka »
06 1.9 TDI Owner. Retrofits: Bixenons, Drls, Full GT/GTI exterior, RNS510+MDI+Premium Bluetooth+RVC+OPS, Full Fis, MFSW, Cruise control, TPMS, Polar Fis, Boot pop up and more.. :)
Coding, diagnostic and retrofits in Leeds
Pre coded Can Gateways for battery drain issues with RNS510 and similar headunits
Premium Bluetooth modules/kit
RNS510 Service - codes, maps/firmware updates
Latest V8 West EU maps update service for RNS315

Offline shoaybmakda

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 25
  • -Receive: 54
  • Posts: 1227
Re: MDI + 7p6 Loom
« Reply #6 on: July 28, 2017, 12:33:35 pm »
@Pashka thanks for that - but that would be way beyond my capabilities I wouldn’t know where to start!

Offline Andy

  • Admin
  • Just look at my post count
  • *
  • Thank You
  • -Given: 39
  • -Receive: 442
  • Posts: 10913
    • Email
Re: MDI + 7p6 Loom
« Reply #7 on: July 28, 2017, 01:03:39 pm »
i have this kit in mine and it is workin perfect

Jasonrpkj

  • Guest
MDI 7p6 Loom
« Reply #8 on: September 22, 2017, 10:58:22 am »
Seen that thread and was helpful in some ways but not sure if the mdi shelf and loom has the blue tooth loom as well as its a lot of changing around if it hasnt

Offline lukemk5gti

  • Just look at my post count
  • ******
  • Thank You
  • -Given: 28
  • -Receive: 118
  • Posts: 1845
    • Email
  • My Ride: http://www.mk5golfgti.co.uk/forum/index.php/topic,89715.msg907250.html#msg907250
Re: MDI + 7p6 Loom
« Reply #9 on: October 23, 2017, 02:35:48 pm »
Just my two cents after fitting mine on the weekend.

Sound quality wasn't working just right.

I had to get a hammer and hit the connections into place on my unit to get them fully on and it suddenly picked up in quality.

Although I was using the old MFD2 connections so that could have been the problem