All Things Mk5 > Sat Nav and Car Audio
Tutorial - How to Update RNS-510 Firmware. ***New Links & Firmware*** 19/02/12
toosmiles:
--- Quote from: Shoduchi on June 05, 2015, 05:40:21 pm ---My posts have been erased by a Mod/Admin... :ashamed: Ok, I guess I shouldn't mention publicly the other forum due to legal issues. :laugh:
Why do you say SD card when it's supposed to be DVD+R dual layer? :confused:
--- End quote ---
ive read that you can install this v12 map through the sd card also on gps forum,using the rns maps tool
will the iso build through imageburn be ok?
Shoduchi:
--- Quote from: toosmiles on June 05, 2015, 05:43:20 pm ---
--- Quote from: Shoduchi on June 05, 2015, 05:40:21 pm ---My posts have been erased by a Mod/Admin... :ashamed: Ok, I guess I shouldn't mention publicly the other forum due to legal issues. :laugh:
Why do you say SD card when it's supposed to be DVD+R dual layer? :confused:
--- End quote ---
ive read that you can install this v12 map through the sd card also on gps forum,using the rns maps tool
will the iso build through imageburn be ok?
--- End quote ---
Yes you can, but preferably you do it with a DVD+R DL. If that works well, why bother passing the maps to a SD card?
I'll send you a PM with the link with the info you requested about upgrading the maps with a SD card. :wink:
NorfolkJim:
Morning caps.
New on here but it seems the font of all knowledge for the RNS510!.
I've just obtained one to put in my Aug 2007 Passat Sport TDi 170 (200) to replace the old RCD300. I've recently had an MFD2 in the car which worked fine through my MFD+ on dash.
The RNS510 I obtained is an old one 1TO 035 680A HW: H04 and SW:1000 made 10:12:2007.
I installed it and to start with the screen wouldn't react for putting code in. After disconnection and retry bingo it worked and after putting code in all worked fine except it's asking for map DVD which I don't have............... anyway it doesn't seem to want to connect to the car and won't run off with ignition or link into my MFD+. To me this sounds like the drain issue people talk about as you have to actually switch radio off.
I have downloaded the SWL fix to see if that helps things first and have also downloaded the 4020A Firmware and also the 1200GW fix for power drain (I think).
Mine has the 'i' symbol top right so how do I go about this?
I assume I switch on but must not have key in ignition and then insert the SWL fix and press Setup 'i' and ejct and wait and see. If all works do I then insert 1200GW drain fix or 4020A firmware update??
Lots of questions but what maps should I be hunting for - I know I may have to pay for them but how up to date can I get on it after doing the above??
Many thanks in anticipation - yes I know it's a Passat but there doesn't seem to be a forum like this for them?? After all I do have 200 hp in a 2.0TDi and 430Nm................ :laugh:
NorfolkJim:
Also where and what version maps should I be looking for???? There seem loads
NorfolkJim:
Well it wouldn't take the SWL fix DVD so tried putting in the 4020A DVD and it worked and showed up through the MFD+...................... system re-started and seemed ok. Switched engine on and still seemed ok but didn't switch of radio?? Left it for a while and took key out - switched radio on again and it asked for the SWL disc again and wants to re-load it again!"!!! Why is this?? It also won't accept the battery drain disc 1220GW - what have I done wrong please.....................................
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version