Post by: MPS on February 20, 2017, 08:00:41 am
Thanks
Post by: Tfsi_Mike on February 20, 2017, 08:01:36 am
Have you just turned the wheel lock to lock or followed the adaptation process?
Post by: MPS on February 20, 2017, 08:21:31 am
Post by: fab5freddy on February 20, 2017, 08:57:51 am
Post by: MPS on February 20, 2017, 08:59:24 am
Post by: RetroRaz on February 20, 2017, 09:06:41 am
Sent from my SM-G928F using Tapatalk
Post by: MPS on February 20, 2017, 09:12:19 am
:happy2:
Post by: MPS on February 20, 2017, 09:24:32 am
Post by: MPS on February 20, 2017, 09:47:17 am
Post by: RetroRaz on February 20, 2017, 09:53:45 am
Post by: MPS on February 20, 2017, 10:50:27 am
you dont really need the long coding from anything, just use VCDS to log in to the module and apply basic settings on the 3 channels I mentioned earlier. :)
Is that in 16-steering wheel or 44-steering assist? When I try security code 40168 in 16 it says Controller refused the key, error 35: invalid key
Post by: MPS on February 20, 2017, 11:10:36 am
Post by: RetroRaz on February 20, 2017, 11:43:20 am
Post by: jason_rmh on February 20, 2017, 05:32:48 pm
If there are errors in abs, the basic settings on steering assist will appear to be accepted but basic settings will not stick and warning lights on dash will remain.
Jas
Post by: MPS on February 20, 2017, 06:41:21 pm
My intention was swapping over from an AQ module to a CH as the cruise control doesn't work with AQ [I only found this out after I bought it].
I originally swapped over from my midline [factory fitted] swcm so I could make use of the mfsw buttons I bought. I'm very tempted to say sod it to the idea of mfsw and go back to my midline swcm - at least the cruise control was working with that.
I didn't save the scan at the time but from memory I think it was this code:
01309 - Power Steering Control Module (J500)
01309 - Power Steering Control Module (J500): Implausible Signal
Possible Symptoms
Malfunction Indicator Light (MIL) active
Possible Causes
When found in Brake Electronics (MK60)
Incorrect Steering Aid Characteristic Setting
Incorrect Steering Aid Warning Lamp Setting
Driver Steering Recommendation (DSR) in activated in Brake Electronics but not in the Steering Aid Control Module or vice versa.
Possible Solutions
When found in Brake Electronics (MK60)
Check Brake Electronics Coding
Check Steering Aid Characteristic Setting
Check Steering Aid Warning Lamp Setting
Check Driver Steering Recommendation (DSR) Setting
Which is the correct setting for the DSR and where do I find it in the swcm?
Bloody minefield!! and I've collected 3 modules now!!! :sad1:
Post by: Newbieintown on February 20, 2017, 08:15:41 pm
Post by: MPS on February 21, 2017, 11:06:26 pm
Managed to get the steering to lighten up, still got fault codes in the abs module however, as follows:
Address 03: ABS Brakes Labels: 1K0-907-379-MK60-F.lbl
Control Module Part Number: 1K0 907 379 Q HW: 1K0 907 379 Q
Component and/or Version: ESP FRONT MK60 0102
Software Coding: 0004738
Work Shop Code: WSC 01279 785 00200
3 Faults Found:
01486 - System Function Test Activated
000 - -
00778 - Steering Angle Sensor (G85)
005 - No or Incorrect Basic Setting / Adaptation
01309 - Power Steering Control Module (J500)
008 - Implausible Signal
The ABS, ESP and TPMS lights are also lit up.
Is it safe to drive as it is? :scared:
Post by: r5gtt on February 22, 2017, 12:40:21 am
My steering works fine with no dash mil lights.
Post by: MPS on February 22, 2017, 01:03:19 am
Post by: jason_rmh on February 22, 2017, 06:44:16 am
This is ok, once all other errors are sorted, we can deal with this one by the completing the test. Don't worry about it for now...
01486 - System Function Test Activated
000 - -
Quote
00778 - Steering Angle Sensor (G85)This one is due to steering angle and also steering limit stop basic settings needed. Details on Ross tech for the mk60 abs.
005 - No or Incorrect Basic Setting / Adaptation
However, I don't think you will be able to clear it while you have the 01309 error.
Quote
01309 - Power Steering Control Module (J500)This will be the cause of your problems.
008 - Implausible Signal
I would remove and refit and check that all connections are definitely in place.
Also, is the steering module coded in 44 steering assist? If not, this might be cause of your problems.
If your horn doesn't work and steering wheel buttons do not light up, either there is a connection problem or a coding issue.
Other option is to disconnect battery for 20mins and try again .
Quote
The ABS, ESP and TPMS lights are also lit up.It's ok to drive but be aware, your power steering may not function and braking may not be as good, abs may kick in when breaking at traffic lights, junctions etc
Jas
Post by: The Red Warrior on February 22, 2017, 06:59:43 am
Right, got a bit further,
Managed to get the steering to lighten up, still got fault codes in the abs module however, as follows:
Address 03: ABS Brakes Labels: 1K0-907-379-MK60-F.lbl
Control Module Part Number: 1K0 907 379 Q HW: 1K0 907 379 Q
Component and/or Version: ESP FRONT MK60 0102
Software Coding: 0004738
Work Shop Code: WSC 01279 785 00200
3 Faults Found:
01486 - System Function Test Activated
000 - -
00778 - Steering Angle Sensor (G85)
005 - No or Incorrect Basic Setting / Adaptation
01309 - Power Steering Control Module (J500)
008 - Implausible Signal
The ABS, ESP and TPMS lights are also lit up.
Is it safe to drive as it is? :scared:
Push and hold both your ABS/ESP and TPMS buttons together. Hold them down for about 5 seconds. You should hear a 'bong' sound and the lights will go out.
Post by: jason_rmh on February 22, 2017, 07:32:50 am
If you have the wrong coding, it could cause a communication issue.
Post by: MPS on February 22, 2017, 12:06:55 pm
If your horn doesn't work and steering wheel buttons do not light up, either there is a connection problem or a coding issue.
Jas
Thanks again for your help
See this is the thing, the horn and the buttons aren't working, but the buttons do light up.
Matt
Post by: Tfsi_Mike on February 22, 2017, 05:37:45 pm
In the past I had loss of button function and loss of horn and it was faulty buttons
Post by: MPS on February 22, 2017, 06:25:58 pm
In the past I had loss of button function and loss of horn and it was faulty buttons
I wonder if its because I'm trying to use the old type [pre 2005.5] buttons with a newish generation [CH] steering wheel control module?
Post by: jason_rmh on February 24, 2017, 12:12:57 am
Ive been out to my car and got a few screen shots for you, a few things to try to narrow this down:
First, goto module 16 - Steering.
Measuring blocks. Check group 6.
This should confirm if there is communication with the module:
(https://www.mk5golfgti.co.uk/forum/proxy.php?request=http%3A%2F%2Fdaz.co%2Fmedia%2Fax_jas%2FVCDS%2F23-02-2017_18-07-01_zpsaq9zshl5.png&hash=3f72aaea7a010a8b0f16f3be0901282ce1b7c452)
Next, check group 4.
(https://www.mk5golfgti.co.uk/forum/proxy.php?request=http%3A%2F%2Fdaz.co%2Fmedia%2Fax_jas%2FVCDS%2F23-02-2017_18-11-09_zpsphz2zcmf.png&hash=de193a14a24c46e9809d77d7412c641601373933)
Turn the steering wheel while monitoring group 4.
You will probably find that the steering angle DOES NOT change wheel you turn the wheel.
It should, but isnt due to the issue we are trying to solve.
Now goto basic settings in module 44 - Steering Assist.
Check group 7.
(https://www.mk5golfgti.co.uk/forum/proxy.php?request=http%3A%2F%2Fdaz.co%2Fmedia%2Fax_jas%2FVCDS%2F23-02-2017_18-10-00_zpscjiyab47.png&hash=5463649c6a014a27c14b1277c62f1e87add2ce46)
Here you should have 'Basic Setting' and 'Init'.
This should say 'OK' and 'Steering Ang Init' which means basic settings are ok and the G85 is initialised.
Yours will most likely say 'NOT OK' and 'Not Init'
Now, I suspect coding may be part of the problem.
Still in module 16 - Steering, check the coding:
(https://www.mk5golfgti.co.uk/forum/proxy.php?request=http%3A%2F%2Fdaz.co%2Fmedia%2Fax_jas%2FVCDS%2F23-02-2017_18-05-39_zps4by8dple.png&hash=753c116a49f919c6c0b600c06ea6b1af48dffd45)
Steering module supports old and new communication (LIN) versions.
This is why the CH module is popular as it supports both Mk5 and Mk6 MFSW.
Hover over the coding box and the bubble will appear, giving you the options:
(https://www.mk5golfgti.co.uk/forum/proxy.php?request=http%3A%2F%2Fdaz.co%2Fmedia%2Fax_jas%2FVCDS%2F23-02-2017_18-05-11_zps08t6jrre.png&hash=0da69b4a993b95cbd8473e0025934362c0daff5e)
Pay attention to the 5th digit (0xxx?xx: Multi-Function Steering Wheel):
This is where you tell the car which communication the module is to use:
options 1 to 4 = LIN 1.3 (If you are fitting a Mk5 MFSW)
options 5 to 8 = LIN 2.0 (If you are fitting a Mk6 MFSW)
Quote
0xxx?xx: Multi-Function Steering Wheel
0 = Multi-Function Steering Wheel not installed
1 or 5 = Multi-Function Steering Wheel w/o Tiptronic and w/o Push-To-Talk (PTT) installed
2 or 6 = Multi-Function Steering Wheel with Tiptronic and no Push-To-Talk (PTT) installed
3 or 7 = Multi-Function Steering Wheel w/o Tiptronic and with Push-To-Talk (PTT) installed
4 or 8 = Multi-Function Steering Wheel with Tiptronic and with Push-To-Talk (PTT) installed
For example, if you are fitting a Mk5 MFSW, with manual gear box ando do not have PTT (voice control), select 1.
My coding is '0000532'.
I have Mk6 MFSW, Manual, Cruise control, button on wiper stalk, No PTT.
So, take a note of your existing coding and check it is correct.
If not update it and see if it sorts out the communication issue.
Report back and we can go from there.
Jas
Post by: MPS on February 24, 2017, 08:42:24 am
Post by: jason_rmh on February 24, 2017, 08:43:16 am
Jas, you're a star, what's your PayPal Addy, have a few pints on me.Has it worked? Was it coding? :)
Post by: MPS on February 24, 2017, 08:49:38 am
Post by: jason_rmh on February 24, 2017, 08:51:46 am
Keep us posted.
I had an issue with mine last week so know how frustrating it is trying to decipher what VCDS is trying to tell you.
Jas
Post by: ducman77 on February 24, 2017, 12:06:09 pm
It's helpful replies like Jas's that make mk5golfgti.co.uk such a brilliant resource!!
Fair Play lads :smiley: :happy2:
And of course I hope you get sorted Jas.... I've had similar issues to youin the past an they're a PAIN!!
Post by: MPS on February 25, 2017, 09:27:55 pm
The story goes like this:
The coding was one digit out on the steering wheel module: I've got an older version of vagcom so I didn't realise there was 2 settings depending on which version of LIN you have, v1.3 or v2.0. My coding was 0000134. [Mk5 MFSW]
and a bonus is my mute button works for the first time ever now!!! :grin: After having the mfsw buttons for a year. Small point but always bugged me haha. The source button directly underneath it has never worked though, I think it was only designed to work with the mfd2 and rcd300, if anyone knows otherwise, please let me know!
Found a reasonably deserted mini[ish] roundabout with just the right radius to enable me to complete the esp initialisation, the 90 to 180 degree thing is reasonably easy to do following the youtube how to vid. The hardest part is finding a deserted roundabout of just the right size.
Now the strange part, all dash lights gone, full autoscan done on vcds, no error codes, except one - the original power steering J500 fault code is stubbornly refusing to clear? :confused: It is exactly the same code as in my previous posts.
Apart from that, it is fine.
Thanks again for your help folks
Matt :drinking:
Post by: jason_rmh on February 25, 2017, 09:32:48 pm
'Air punch'
Post by: MPS on February 25, 2017, 09:40:38 pm
Post by: MPS on February 25, 2017, 09:52:00 pm
My car was made around 2005.5 so around the changeover point.
Frontbrakes (Sensor Cluster OLD):
+0000005 = FS III 54 15" (PR-1ZF/1ZM/1ZC)
+0000006 = FN III 54 15"/16" (PR-1ZE/1LJ/1ZP/1ZD/1LL)
+0000009 = FRNG 57 17" (PR-1LK)
Frontbrakes (Sensor Cluster NEW):
+0000001 = FS III 54 15" (PR-1ZF/1ZM/1ZC)
+0000002 = FN III 54 15"/16" (PR-1ZE/1LJ/1ZP/1ZD/1LL)
+0000008 = FRNG 57 17" (PR-1LK)
Post by: jason_rmh on February 25, 2017, 10:05:58 pm
So, I'm not sure the j500 is related to the SWCM, or you may have blown a fuse while installing the new module?
Goto module 19-CAN Gateway, Measuring Blocks > Group - 152
Field 2 should display the CAN-Bus status of the J500-Power Steering Control Module.
You should see a 1.
If you see a 0 then there is a communication issue between the CAN-Bus and the J500, which may indicate a broken wire.
Then, check fuses.
Engine bay, Fuse 3 (110-amp) (terminal 30)].
And there is a black wire from fuse 3 to J500, check that for breaks if you can.
Check driver's side fuse box, fuse 15 also, this gives ignition power to j500 I think.
Jas
Post by: MPS on February 25, 2017, 10:30:31 pm
Although that doesn't quite fit right as with any of them rosstech says you'd expect the MIL light to be on, which it isn't.
I'll try the coding tweak tomorrow and let you know!
So what actual part is the J500? Is it integrated into the steering wheel module?
Post by: jason_rmh on February 25, 2017, 10:38:27 pm
It may be that some basic settings need doing somewhere?
J500 is the power steering control module.
Do you have any faults in module 16 (steering wheel) or 44 (steering assist)?
Post by: MPS on February 25, 2017, 10:55:51 pm
You're right, I would have expected a red or amber power steering light to be on.
It may be that some basic settings need doing somewhere?
J500 is the power steering control module.
So where is that physically on the car? Just curious.
Do you have any faults in module 16 (steering wheel) or 44 (steering assist)?
No, none!! Weird, eh? :laugh:
Post by: jason_rmh on February 25, 2017, 11:36:51 pm
So where is that physically on the car? Just curious.
I think the module is directly mounted on the power steering rack.
The steering rack is mounted on the subframe, close to the anti roll bar.
Post by: r5gtt on February 26, 2017, 02:20:59 pm
Post by: Kai96 on February 27, 2017, 07:52:27 pm
I will update tomorrow once I've picked the car up
Post by: jason_rmh on February 27, 2017, 08:03:12 pm
I'm basically having the same problem installed a MK6 GTI MFSW I have the steering wheel tyre pressure and traction control lights on the dash. Weird thing is I have power steering when I'm idling in Park but as soon as I put it into D and start driving I lose my power steering. Taking the car to a specialist tomorrow to have my highlines coded in so hopefully he'll be able to sort the steering wheel to.Kai, do you have VCDS? Your issue is probably coding and basic settings for steering angle / steering limit etc
I will update tomorrow once I've picked the car up
For dsg cars there is also the longitudinal acceleration sensor to be set.
Are you getting the J500 error?
Post by: Kai96 on February 27, 2017, 08:16:02 pm
I'm basically having the same problem installed a MK6 GTI MFSW I have the steering wheel tyre pressure and traction control lights on the dash. Weird thing is I have power steering when I'm idling in Park but as soon as I put it into D and start driving I lose my power steering. Taking the car to a specialist tomorrow to have my highlines coded in so hopefully he'll be able to sort the steering wheel to.Kai, do you have VCDS? Your issue is probably coding and basic settings for steering angle / steering limit etc
I will update tomorrow once I've picked the car up
For dsg cars there is also the longitudinal acceleration sensor to be set.
Are you getting the J500 error?
Took it to my friend who has VCDS today and all the faults got cleared accept for the steering ones like assisted power steering but I can't remember 100% what they were. I just know two of them weren't clearing. We were really close to fixing it as we followed all the advice in this thread and it was just something near the end we couldn't get right
Sorry i'm not that clued up on VCDS so where would I find the settings for the longitudinal acceleration that needs to be set ?
Post by: jason_rmh on March 01, 2017, 09:17:00 am
Jas
Post by: MPS on March 01, 2017, 06:07:32 pm
Also, something else I can't get my head around, in 03-ABS Brakes adaptation, channel 1 is set to Tire Pressure - 16 inch? There are 3 values you can select, 0 - 15 inch, 1 - 16 inch and 2 - 16 inch? Confusing and I'm guessing it has nothing to do with 18" wheels?
Also channel 9 is set to 'brake assist - center', the other possible settings are small and 2 large?
Cheers
Matt
Post by: Kai96 on March 01, 2017, 06:44:38 pm
Post by: jason_rmh on March 01, 2017, 06:47:54 pm
@r5gtt does this help you out?
Post by: MPS on March 01, 2017, 07:28:21 pm
Good work both.
@R5gtt does this help you out?
Any ideas about those tire pressure settings @jason_rmh (http://www.mk5golfgti.co.uk/forum/index.php?action=profile;u=4481)?
Post by: r5gtt on March 01, 2017, 08:08:58 pm
Good work both.havent had the chance to try it yet mate @jason_rmh (http://www.mk5golfgti.co.uk/forum/index.php?action=profile;u=4481) but will update this post as soon as I do thanks :drinking:
@r5gtt (http://www.mk5golfgti.co.uk/forum/index.php?action=profile;u=11199) does this help you out?
Post by: jason_rmh on March 01, 2017, 08:17:34 pm
03-ABS Brakes adaptation, channel 1 is set to Tire Pressure - 16 inch? There are 3 values you can select, 0 - 15 inch, 1 - 16 inch and 2 - 16 inch? Confusing and I'm guessing it has nothing to do with 18" wheels?
I think no 2 may be a typo in the label file and is probably for 18".
I'll check mine and let you know
Post by: r5gtt on March 01, 2017, 10:21:47 pm
you cannot change this as I've just tried03-ABS Brakes adaptation, channel 1 is set to Tire Pressure - 16 inch? There are 3 values you can select, 0 - 15 inch, 1 - 16 inch and 2 - 16 inch? Confusing and I'm guessing it has nothing to do with 18" wheels?
I think no 2 may be a typo in the label file and is probably for 18".
I'll check mine and let you know
Post by: r5gtt on March 02, 2017, 12:15:51 am
Steering wheel is showing 0
ABS is the only thing showing weird readings
I haven't checked the fuses but will do that on my next outing to the car if that makes a difference
(https://www.mk5golfgti.co.uk/forum/proxy.php?request=http%3A%2F%2Fi1374.photobucket.com%2Falbums%2Fag433%2FSandy1786%2FIMG_4913.jpg&hash=6eefb7b256920ad7ec91c00f56df1b06b6c1e8f3)
(https://www.mk5golfgti.co.uk/forum/proxy.php?request=http%3A%2F%2Fi1374.photobucket.com%2Falbums%2Fag433%2FSandy1786%2FIMG_4919.jpg&hash=b774e7b75f839182a5d415180734d59beb9a42e2)
(https://www.mk5golfgti.co.uk/forum/proxy.php?request=http%3A%2F%2Fi1374.photobucket.com%2Falbums%2Fag433%2FSandy1786%2FIMG_4916.jpg&hash=2a4f13e7ed2463a2a04beceb794edab3c260b665)
@jason_rmh (http://www.mk5golfgti.co.uk/forum/index.php?action=profile;u=4481)
Post by: jason_rmh on March 02, 2017, 05:21:29 am
Post by: r5gtt on March 02, 2017, 03:56:40 pm
Post by: jason_rmh on March 02, 2017, 04:29:06 pm
...
Goto module 19-CAN Gateway, Measuring Blocks > Group - 152
Field 2 should display the CAN-Bus status of the J500-Power Steering Control Module.
You should see a 1.
If you see a 0 then there is a communication issue between the CAN-Bus and the J500, which may indicate a broken wire.
Then, check fuses.
Engine bay, Fuse 3 (110-amp) (terminal 30)].
And there is a black wire from fuse 3 to J500, check that for breaks if you can.
Check driver's side fuse box, fuse 15 also, this gives ignition power to j500
...
Post by: r5gtt on March 02, 2017, 06:41:11 pm
I said module 19, can gateway...oh rightio thanks I did check that but remembering getting an error but will double check that and also check the fuses this weekend to make sure non have blown. Thanks...
Goto module 19-CAN Gateway, Measuring Blocks > Group - 152
Field 2 should display the CAN-Bus status of the J500-Power Steering Control Module.
You should see a 1.
If you see a 0 then there is a communication issue between the CAN-Bus and the J500, which may indicate a broken wire.
Then, check fuses.
Engine bay, Fuse 3 (110-amp) (terminal 30)].
And there is a black wire from fuse 3 to J500, check that for breaks if you can.
Check driver's side fuse box, fuse 15 also, this gives ignition power to j500
...
Post by: MPS on March 13, 2017, 10:09:36 pm
Any ideas @jason_rmh (http://www.mk5golfgti.co.uk/forum/index.php?action=profile;u=4481) ?
Post by: NitrousOxide on March 27, 2020, 11:08:34 pm
Here is the AUTOSCAN after the swap with the new steering wheel and second-hand control module with airbag (however horn does not work).
Code: [Select]
Friday,27,March,2020,15:22:39:39976VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 19.6.2.2 (x64)
Data version: 20200210 DS308.0
www.Ross-Tech.com
Dealer/Shop Name: Matthew Taylor
Workshop Code: 123 12345 012345
VIN: WVWZZZ1KZ8W111078 License Plate:
Chassis Type: 1K-VW35 (7N0)
Scan: 01 02 03 08 09 15 16 17 19 25 42 44 46 52 55 56
VIN: WVWZZZ1KZ8W111078 Mileage: 191360km-118905miles
01-Engine -- Status: OK 0000
02-Auto Trans -- Status: Malfunction 0010
03-ABS Brakes -- Status: Malfunction 0010
04-Steering Angle -- Status: Cannot be reached 1100
08-Auto HVAC -- Status: Malfunction 0010
09-Cent. Elect. -- Status: OK 0000
15-Airbags -- Status: Malfunction 0010
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: Malfunction 0010
25-Immobilizer -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: Malfunction 0010
46-Central Conv. -- Status: Malfunction 0010
52-Door Elect, Pass. -- Status: OK 0000
55-Headlight Range -- Status: Malfunction 0010
56-Radio -- Status: Malfunction 0010
-------------------------------------------------------------------------------
Address 01: Engine Labels:. 06F-907-115-AXX.clb
Part No SW: 1K0 907 115 R HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH16--- Serial number: VWX7Z0G83NA8OV
Coding: 040300101C070160
Shop #: WSC 66565 257 00032
VCID: 354FD8585CDD5EE746-8060
No fault code found.
Readiness: 0110 0001
-------------------------------------------------------------------------------
Address 02: Auto Trans Labels: 02E-927-770.clb
Part No SW: 02E 300 044 J HW: 02E 927 770 AD
Component: GSG DSG 082 1407
Revision: 05108020 Serial number: 00001009061622
Coding: 0000020
Shop #: WSC 04940 001 00001
VCID: 1C192DFCDF37EFAF59-8048
1 Fault Found:
18036 - Powertrain Data Bus
P1628 - 000 - Missing Message from Steering Angle Sensor
Freeze Frame:
Fault Status: 01100000
Fault Priority: 0
Fault Frequency: 255
Reset counter: 40
Mileage: 191365 km
Time Indication: 0
Date: 2014.08.18
Time: 00:07:27
-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 1K0-907-379-MK60-F.lbl
Part No SW: 1K0 907 379 AC HW: 1K0 907 379 AC
Component: ESP FRONT MK60 0101
Revision: 00H11001
Coding: 0004738
Shop #: WSC 12345 123 12345
VCID: 73CB2640122900D7A8-8026
2 Faults Found:
00778 - Steering Angle Sensor (G85)
000 - -
00778 - Steering Angle Sensor (G85)
004 - No Signal/Communication
-------------------------------------------------------------------------------
Address 08: Auto HVAC (J255) Labels:| 5K0-907-044.clb
Part No SW: 5K0 907 044 ES HW: 5K0 907 044 ES
Component: Climatronic H18 1112
Revision: 00001004
Coding: 0000014002
Shop #: WSC 12345 123 61029
ASAM Dataset: EV_Climatronic A01010
ROD: EV_ClimaAutoBasis_VW36.rod
VCID: 0021798C9B9F2B4FA5-8054
1 Fault Found:
9479189 - Signal Line for Air Quality Sensor
B10A4 15 [009] - Open or Short to Plus
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 3
Fault Frequency: 3
Reset counter: 81
Mileage: 191365 km
Date: 2020.03.27
Time: 00:07:28
-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels:. 3C0-937-049-30-H.lbl
Part No SW: 3C0 937 049 AJ HW: 3C0 937 049 AJ
Component: Bordnetz-SG H54 2202
Revision: 00H54000 Serial number: 01000007456322
Coding: F78F8B270004800047140A001400008000191C075C00010D000000000000
Shop #: WSC 12345 111 45725
VCID: 71C72C48683532C75A-8024
Subsystem 1 - Part No: 1K2 955 119 E Labels: 1KX-955-119.CLB
Component: Wischer 300807 021 0501
Coding: 00039861
Shop #: WSC 12345
Subsystem 2 - Part No: 1K0 955 559 AF Labels: 1K0-955-559-AF.CLB
Component: RLS 130907 046 0204
Coding: 00208933
Shop #: WSC 12345
No fault code found.
-------------------------------------------------------------------------------
Address 15: Airbags Labels: 1K0-909-605.lbl
Part No SW: 1K0 909 605 T HW: 1K0 909 605 T
Component: 3A AIRBAG VW8 020 2300
Revision: 05020000 Serial number: 0038PD1FKU0T
Coding: 0013121
Shop #: WSC 01269 785 00200
VCID: 3D5FC07864ED86A78E-8068
Subsystem 1 - Serial number: 6332MSME2C406B29H
Subsystem 2 - Serial number: 6342MSME2C42223ED
Subsystem 3 - Serial number: 6352QSME3D213635D
Subsystem 4 - Serial number: 6362QSME3C0B0C41L
4 Faults Found:
00655 - Seat Belt Tensioner Igniter; Passenger Side (N154)
001 - Upper Limit Exceeded - MIL ON
00589 - Airbag Igniter 1; Passenger Side (N131)
001 - Upper Limit Exceeded - MIL ON
01228 - Airbag Cut-Off Switch for Passenger Side (E224)
010 - Open or Short to Plus - MIL ON
02756 - Redundant signal path of Airbag cut-off switch - front passenger side (E224)
010 - Open or Short to Plus - MIL ON
-------------------------------------------------------------------------------
Address 16: Steering wheel Labels: 1K0-953-549-MY9.lbl
Part No SW: 1K0 953 549 CD HW: 1K0 953 549 CD
Component: J0527 056 0111
Coding: 0001632
Shop #: WSC 01357 011 00200
VCID: 76CD1F54015B15FF8F-8022
Subsystem 1 - Part No: 5K0 959 542 Labels: 3C8-959-537.CLB
Component: E221__MFL-TAS H06 0010
Coding: 00000131
Shop #: WSC 00000
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments (J285) Labels:| 5K0-920-xxx-17.clb-SRI1
Part No SW: 5K6 920 972 E HW: 5K6 920 972 E
Component: KOMBI H04 0617
Serial number: 00000000000000
Coding: 170C01
Shop #: WSC 12345 123 61029
ASAM Dataset: EV_Kombi_UDS_VDD_RM09 A04114
ROD: EV_Kombi_UDS_VDD_RM09_004_VW32.rod
VCID: 3851D16C83CFA38F5D-806C
No fault code found.
-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533) Labels:. 7N0-907-530-V2.clb
Part No SW: 7N0 907 530 M HW: 1K0 907 951
Component: J533 Gateway H42 1623
Revision: H42 Serial number: 030312F2002329
Coding: 350001
Shop #: WSC 12345 123 61029
VCID: 3A55CB64B5C3B19FAB-806E
1 Fault Found:
00778 - Steering Angle Sensor (G85)
004 - No Signal/Communication
Freeze Frame:
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 81
Mileage: 191365 km
Time Indication: 0
Date: 2014.08.18
Time: 00:07:38
-------------------------------------------------------------------------------
Address 25: Immobilizer (J334) Labels:| 5K0-920-xxx-25.clb
Part No SW: 5K0 953 234 HW: 5K0 953 234
Component: IMMO H04 0617
Serial number: 00000000000000
Coding: 000000
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_Immo_UDS_VDD_RM09 A03009
ROD: EV_Immo_UDS_VDD_RM09.rod
VCID: 6AF53B248DE3C11F1B-803E
No fault code found.
-------------------------------------------------------------------------------
Address 42: Door Elect, Driver Labels:. 1K0-959-701-MIN3.clb
Part No SW: 1K0 959 701 M HW: 1K0 959 701 M
Component: Tuer-SG 006 120B
Coding: 0000560
Shop #: WSC 12345 123 12345
VCID: 3851D16C4BCFA38F5D-806C
No fault code found.
-------------------------------------------------------------------------------
Address 44: Steering Assist Labels: 1K0-909-14x-GEN3.clb
Part No: 1K0 909 144 P
Component: EPS_ZFLS Kl. 207 3305
Revision: 00H22000
Shop #: WSC 00028 028 00001
VCID: 3753D25046D1ACF754-8062
1 Fault Found:
03803 - Steering Angle Sensor for Steering Aid
000 - - - MIL ON
Freeze Frame:
Fault Status: 11100000
Fault Priority: 2
Fault Frequency: 1
Reset counter: 255
Mileage: 191365 km
Time Indication: 0
Date: 2014.08.18
Time: 00:07:38
Freeze Frame:
Battery Volts: 13.6 V
DU
Temperature: 40.0°C
Count: 2
Steering Angle: 0.00°
Count: 1
SteerAng n.Init
-------------------------------------------------------------------------------
Address 46: Central Conv. Labels:. 1K0-959-433-MAX.clb
Part No SW: 1K0 959 433 BT HW: 1K0 959 433 BT
Component: KSG PQ35 G2 020 0204
Revision: 00020000 Serial number: 00000000000000
Coding: 98900A085103007F42000F0FF0CA5A0610BC40
Shop #: WSC 12345 111 45725
VCID: 032B768042893057B8-8056
Subsystem 1 - Part No: 1K0 951 605 C
Component: LIN BACKUP HORN H03 1301
Subsystem 2 - Component: NGS n.mounted
Subsystem 3 - Component: IRUE n.mounted
1 Fault Found:
01134 - Alarm Horn (H12)
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 4
Fault Frequency: 1
Reset counter: 81
Mileage: 191365 km
Time Indication: 0
Date: 2014.08.18
Time: 00:07:39
-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. Labels:. 1K0-959-702-MIN3.clb
Part No SW: 1K0 959 702 M HW: 1K0 959 702 M
Component: Tuer-SG 006 120B
Coding: 0000564
Shop #: WSC 12345 123 12345
VCID: 3957D46870C5BA87A2-806C
No fault code found.
-------------------------------------------------------------------------------
Address 55: Headlight Range Labels: 1T0-907-357.lbl
Part No: 1T0 907 357
Component: Dynamische LWR 0003
Coding: 0000003
Shop #: WSC 00000 785 00200
VCID: 74C9255C172707EFB1-8020
1 Fault Found:
00778 - Steering Angle Sensor (G85)
004 - No Signal/Communication
-------------------------------------------------------------------------------
Address 56: Radio (J503) Labels:. 5M0-035-1xx-56.clb
Part No SW: 1K0 035 180 AE HW: 1K0 035 180 AE
Component: Radio Prem-8 H02 0016
Revision: -----16S Serial number: VWZ4Z7L3180243
Coding: 00000401000005
Shop #: WSC 12345 123 61029
VCID: 63EB560062C99057D8-8036
4 Faults Found:
00821 - Antenna 2 for Radio (R93)
011 - Open Circuit
Freeze Frame:
Fault Status: 01101011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 81
Mileage: 191365 km
Time Indication: 0
Date: 2014.08.18
Time: 00:07:42
02633 - Antenna for Satellite Tuner
011 - Open Circuit
Freeze Frame:
Fault Status: 01101011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 81
Mileage: 191365 km
Time Indication: 0
Date: 2014.08.18
Time: 00:07:42
02635 - Tuner Not Enabled/Activated
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 7
Fault Frequency: 1
Reset counter: 81
Mileage: 191365 km
Time Indication: 0
Date: 2014.08.18
Time: 00:07:42
00872 - Bass Speaker Rear Left (R15)
011 - Open Circuit
Freeze Frame:
Fault Status: 01101011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 81
Mileage: 191365 km
Time Indication: 0
Date: 2014.08.18
Time: 00:10:51
End-------------------------(Elapsed Time: 01:24)--------------------------
Here is the AUTOSCAN prior to the swap with the horn working on my 8-button steering wheel, but original clock-spring and steering wheel control module
Code: [Select]
Friday,07,February,2020,06:36:12:39976VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 19.6.2.0 (x64)
Data version: 20190930 DS308.0
www.Ross-Tech.com
Dealer/Shop Name: Matthew Taylor
Workshop Code: 123 12345 012345
VIN: WVWZZZ1KZ8W111078 License Plate:
Chassis Type: 1K-VW35 (7N0)
Scan: 01 02 03 08 09 15 16 17 19 25 42 44 46 52 55 56 77
VIN: WVWZZZ1KZ8W111078 Mileage: 190190km-118178miles
01-Engine -- Status: Malfunction 0010
02-Auto Trans -- Status: OK 0000
03-ABS Brakes -- Status: Malfunction 0010
04-Steering Angle -- Status: OK 0000
08-Auto HVAC -- Status: Malfunction 0010
09-Cent. Elect. -- Status: Malfunction 0010
15-Airbags -- Status: Malfunction 0010
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: Malfunction 0010
25-Immobilizer -- Status: OK 0000
42-Door Elect, Driver -- Status: Malfunction 0010
44-Steering Assist -- Status: Malfunction 0010
46-Central Conv. -- Status: Malfunction 0010
52-Door Elect, Pass. -- Status: OK 0000
55-Headlight Range -- Status: OK 0000
56-Radio -- Status: Malfunction 0010
77-Telephone -- Status: Sporadic communication error 1000
-------------------------------------------------------------------------------
Address 01: Engine Labels:. 06F-907-115-AXX.clb
Part No SW: 1K0 907 115 R HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH16--- Serial number: VWX7Z0G83NA8OV
Coding: 040300101C070160
Shop #: WSC 66565 257 00032
VCID: 354FD8585CDD5EE744-8060
1 Fault Found:
000054 - Oxygen (Lambda) Sensor B1 S2: Heating Circuit
P0036 - 004 - Malfunction / Open Circuit
Freeze Frame:
Fault Status: 01100100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 255
Mileage: 190182 km
Time Indication: 0
Date: 2020.02.07
Time: 04:28:14
Freeze Frame:
RPM: 823 /min
Load: 28.2 %
Speed: 0.0 km/h
Temperature: 89.0°C
Temperature: 57.0°C
Absolute Pres.: 1000.0 mbar
Voltage: 13.589 V
Readiness: 0110 0101
-------------------------------------------------------------------------------
Address 02: Auto Trans Labels: 02E-927-770.clb
Part No SW: 02E 300 044 J HW: 02E 927 770 AD
Component: GSG DSG 082 1407
Revision: 05108020 Serial number: 00001009061622
Coding: 0000020
Shop #: WSC 04940 001 00001
VCID: 1C192DFCDF37EFAF5B-8048
No fault code found.
-------------------------------------------------------------------------------
Address 03: ABS Brakes Labels: 1K0-907-379-MK60-F.lbl
Part No SW: 1K0 907 379 AC HW: 1K0 907 379 AC
Component: ESP FRONT MK60 0101
Revision: 00H11001
Coding: 0004738
Shop #: WSC 12345 123 12345
VCID: 73CB2640122900D7AA-8026
7 Faults Found:
00474 - Control Module for Immobilizer
004 - No Signal/Communication - Intermittent
00668 - Supply Voltage Terminal 30
002 - Lower Limit Exceeded - Intermittent
01044 - Control Module Incorrectly Coded
008 - Implausible Signal - Intermittent
01317 - Control Module in Instrument Cluster (J285)
004 - No Signal/Communication - Intermittent
01435 - Brake Pressure Sensor 1 (G201)
005 - No or Incorrect Basic Setting / Adaptation
00778 - Steering Angle Sensor (G85)
005 - No or Incorrect Basic Setting / Adaptation
01423 - Lateral Acceleration Sensor (G200)
005 - No or Incorrect Basic Setting / Adaptation
-------------------------------------------------------------------------------
Address 08: Auto HVAC (J255) Labels:| 5K0-907-044.clb
Part No SW: 5K0 907 044 ES HW: 5K0 907 044 ES
Component: Climatronic H18 1112
Revision: 00001004
Coding: 0000014002
Shop #: WSC 12345 123 61029
ASAM Dataset: EV_Climatronic A01010
ROD: EV_ClimaAutoBasis_VW36.rod
VCID: 0021798C9B9F2B4FA7-8054
1 Fault Found:
9479189 - Signal Line for Air Quality Sensor
B10A4 15 [009] - Open or Short to Plus
Confirmed - Tested Since Memory Clear
Freeze Frame:
Fault Status: 00000001
Fault Priority: 3
Fault Frequency: 4
Reset counter: 243
Mileage: 190182 km
Date: 2020.02.07
Time: 04:28:07
-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels:. 3C0-937-049-30-H.lbl
Part No SW: 3C0 937 049 AJ HW: 3C0 937 049 AJ
Component: Bordnetz-SG H54 2202
Revision: 00H54000 Serial number: 01000007456322
Coding: F78F8B270004800047140A001400008000197E075C00010C000000000000
Shop #: WSC 12345 123 12345
VCID: 71C72C48683532C758-8024
Subsystem 1 - Part No: 1K2 955 119 E Labels: 1KX-955-119.CLB
Component: Wischer 300807 021 0501
Coding: 00039861
Shop #: WSC 12345
Subsystem 2 - Part No: 1K0 955 559 AF Labels: 1K0-955-559-AF.CLB
Component: RLS 130907 046 0204
Coding: 00208933
Shop #: WSC 12345
1 Fault Found:
01502 - Bulb for Rear Fog; Left (L46)
012 - Electrical Fault in Circuit
Freeze Frame:
Fault Status: 01101100
Fault Priority: 2
Fault Frequency: 1
Reset counter: 243
Mileage: 190182 km
Time Indication: 0
Date: 2005.09.13
Time: 31:63:63
Freeze Frame:
ON
Voltage: 13.20 V
ON
ON
OFF
OFF
OFF
-------------------------------------------------------------------------------
Address 15: Airbags Labels: 1K0-909-605.lbl
Part No SW: 1K0 909 605 T HW: 1K0 909 605 T
Component: 3A AIRBAG VW8 020 2300
Revision: 05020000 Serial number: 0038PD1FKU0T
Coding: 0013121
Shop #: WSC 01269 785 00200
VCID: 3D5FC07864ED86A78C-8068
Subsystem 1 - Serial number: 6332MSME2C406B29H
Subsystem 2 - Serial number: 6342MSME2C42223ED
Subsystem 3 - Serial number: 6352QSME3D213635D
Subsystem 4 - Serial number: 6362QSME3C0B0C41L
5 Faults Found:
00588 - Airbag Igniter; Driver Side (N95)
001 - Upper Limit Exceeded - MIL ON
00589 - Airbag Igniter 1; Passenger Side (N131)
001 - Upper Limit Exceeded - MIL ON
01228 - Airbag Cut-Off Switch for Passenger Side (E224)
010 - Open or Short to Plus - MIL ON
02756 - Redundant signal path of Airbag cut-off switch - front passenger side (E224)
010 - Open or Short to Plus - MIL ON
00655 - Seat Belt Tensioner Igniter; Passenger Side (N154)
001 - Upper Limit Exceeded - MIL ON
-------------------------------------------------------------------------------
Address 16: Steering wheel Labels: 1K0-953-549-MY8.lbl
Part No SW: 1K0 953 549 AQ HW: 1K0 953 549 AQ
Component: J0527 036 0070
Coding: 0012122
Shop #: WSC 12345 123 12345
VCID: 01277C8858952247A8-8054
Subsystem 1 - Part No: XXXXXXXXXXX
Component: E0221 002 0010
No fault code found.
-------------------------------------------------------------------------------
Address 17: Instruments (J285) Labels:| 5K0-920-xxx-17.clb-SRI1
Part No SW: 5K6 920 972 E HW: 5K6 920 972 E
Component: KOMBI H04 0617
Serial number: 00000000000000
Coding: 170C01
Shop #: WSC 12345 123 61029
ASAM Dataset: EV_Kombi_UDS_VDD_RM09 A04114
ROD: EV_Kombi_UDS_VDD_RM09_004_VW32.rod
VCID: 3851D16C83CFA38F5F-806C
No fault code found.
-------------------------------------------------------------------------------
Address 19: CAN Gateway (J533) Labels:. 7N0-907-530-V2.clb
Part No SW: 7N0 907 530 M HW: 1K0 907 951
Component: J533 Gateway H42 1623
Revision: H42 Serial number: 030312F2002329
Coding: 350001
Shop #: WSC 12345 123 12345
VCID: 3A55CB64B5C3B19FA9-806E
1 Fault Found:
01303 - Telephone Transceiver (R36)
004 - No Signal/Communication - Intermittent
Freeze Frame:
Fault Status: 00100100
Fault Priority: 2
Fault Frequency: 2
Reset counter: 27
Mileage: 190187 km
Time Indication: 0
Date: 2020.02.07
Time: 04:50:41
-------------------------------------------------------------------------------
Address 25: Immobilizer (J334) Labels:| 5K0-920-xxx-25.clb
Part No SW: 5K0 953 234 HW: 5K0 953 234
Component: IMMO H04 0617
Serial number: 00000000000000
Coding: 000000
Shop #: WSC 01357 011 00200
ASAM Dataset: EV_Immo_UDS_VDD_RM09 A03009
ROD: EV_Immo_UDS_VDD_RM09.rod
VCID: 6AF53B248DE3C11F19-803E
No fault code found.
-------------------------------------------------------------------------------
Address 42: Door Elect, Driver Labels:. 1K0-959-701-MIN3.clb
Part No SW: 1K0 959 701 M HW: 1K0 959 701 M
Component: Tuer-SG 006 120B
Coding: 0000564
Shop #: WSC 11111 111 45799
VCID: 3851D16C4BCFA38F5F-806C
1 Fault Found:
00109 - Left Mirror Turn Signal Lamp (L131)
012 - Electrical Fault in Circuit
-------------------------------------------------------------------------------
Address 44: Steering Assist Labels: 1K0-909-14x-GEN3.clb
Part No: 1K0 909 144 P
Component: EPS_ZFLS Kl. 207 3305
Revision: 00H22000
Shop #: WSC 00028 028 00001
VCID: 3753D25046D1ACF756-8062
1 Fault Found:
03803 - Steering Angle Sensor for Steering Aid
005 - No or Incorrect Basic Setting / Adaptation - MIL ON
Freeze Frame:
Fault Status: 11100101
Fault Priority: 2
Fault Frequency: 1
Reset counter: 255
Mileage: 190182 km
Time Indication: 0
Date: 2020.02.07
Time: 04:28:19
Freeze Frame:
Battery Volts: 13.6 V
DU
Temperature: 44.0°C
Count: 3
Steering Angle: 0.00°
Count: 1
SteerAng n.Init
-------------------------------------------------------------------------------
Address 46: Central Conv. Labels:. 1K0-959-433-MAX.clb
Part No SW: 1K0 959 433 BT HW: 1K0 959 433 BT
Component: KSG PQ35 G2 020 0204
Revision: 00020000 Serial number: 00000000000000
Coding: 98900A085103007F42040F0FF00A5A0690BC00
Shop #: WSC 12345 111 45725
VCID: 032B768042893057BA-8056
Subsystem 1 - Part No: 1K0 951 605 C
Component: LIN BACKUP HORN H03 1301
Subsystem 2 - Component: NGS n.mounted
Subsystem 3 - Component: IRUE n.mounted
1 Fault Found:
01134 - Alarm Horn (H12)
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 4
Fault Frequency: 1
Reset counter: 242
Mileage: 190182 km
Time Indication: 0
Date: 2020.02.07
Time: 04:28:19
-------------------------------------------------------------------------------
Address 52: Door Elect, Pass. Labels:. 1K0-959-702-MIN3.clb
Part No SW: 1K0 959 702 M HW: 1K0 959 702 M
Component: Tuer-SG 006 120B
Coding: 0000564
Shop #: WSC 12345 123 12345
VCID: 3957D46870C5BA87A0-806C
No fault code found.
-------------------------------------------------------------------------------
Address 55: Headlight Range Labels: 1T0-907-357.lbl
Part No: 1T0 907 357
Component: Dynamische LWR 0003
Coding: 0000003
Shop #: WSC 00000 785 00200
VCID: 74C9255C172707EFB3-8020
No fault code found.
-------------------------------------------------------------------------------
Address 56: Radio (J503) Labels:. 5M0-035-1xx-56.clb
Part No SW: 1K0 035 180 AE HW: 1K0 035 180 AE
Component: Radio Prem-8 H02 0016
Revision: -----16S Serial number: VWZ4Z7L3180243
Coding: 01000401000005
Shop #: WSC 12345 123 61029
VCID: 63EB560062C99057DA-8036
3 Faults Found:
02633 - Antenna for Satellite Tuner
011 - Open Circuit
Freeze Frame:
Fault Status: 01101011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 242
Mileage: 190182 km
Time Indication: 0
Date: 2020.02.07
Time: 04:28:21
02635 - Tuner Not Enabled/Activated
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 7
Fault Frequency: 1
Reset counter: 242
Mileage: 190182 km
Time Indication: 0
Date: 2020.02.07
Time: 04:28:21
00872 - Bass Speaker Rear Left (R15)
011 - Open Circuit
Freeze Frame:
Fault Status: 01101011
Fault Priority: 5
Fault Frequency: 1
Reset counter: 242
Mileage: 190185 km
Time Indication: 0
Date: 2020.02.07
Time: 04:45:08
-------------------------------------------------------------------------------
Address 77: Telephone
Cannot be reached
End-------------------------(Elapsed Time: 01:29)--------------------------
Can someone please suggest suitable coding for me, as I forgot to look at the configuration from my previous steering wheel configuration information before I pulled the module from the vehicle.