MK5 Golf GTI
All Things Mk5 => Mk5 General Area => Topic started by: Tuffy on May 15, 2010, 01:58:52 pm
-
Hi all.
Trying to change my boot latch over for a new one as old was suffering from white worm.
Now managed to get boot lining out to expose all the nuts a screws i need to remove but doesn't matter what i try i cant remove the rear wiper arm to inable the motor drop out! Wd40, pulled it twisted it and still wont move!!!
You guys had trouble with this? Any ideas?
Thanks in advance guys.
-
The best way I have found is (after using some WD40 on the nut), wrap a soft cloth around the shaft and using a large headed spanner (adjustable ones work well) try to prise the wiper arm off. Then if the motor still won't drop out use a rubber mallet to tap it through.
However IIRC by loosing the wiper motor you can normally get to enough of the screws to remove the boot badge.
-
Yeah it is hard but just need a LOT of pushing and pulling.... then it WILL come off :)
-
Yeah it is hard but just need a LOT of pushing and pulling.... then it WILL come off :)
I've pulled so hard nearly pulled the glass out of the rubbers! :signLOL:
-
The best way I have found is (after using some WD40 on the nut), wrap a soft cloth around the shaft and using a large headed spanner (adjustable ones work well) try to prise the wiper arm off. Then if the motor still won't drop out use a rubber mallet to tap it through.
However IIRC by loosing the wiper motor you can normally get to enough of the screws to remove the boot badge.
Tried the mallet trick too! still wont shift!
-
Which bit is stuck?
Have you got the wiper arm off?
-
Which bit is stuck?
Have you got the wiper arm off?
No wiper arm still on! took the nut off thinking it would just pull off but not a chance!!!
-
You just need to be braver with the mallet.
I have removed around 10 of these on different cars now for the rear camera install and they all required a lot of force.
I still find it easier to prise the wiper arm off with the adjustable spanner and the use the mallet to knock the motor through.
-
You just need to be braver with the mallet.
I have removed around 10 of these on different cars now for the rear camera install and they all required a lot of force.
I still find it easier to prise the wiper arm off with the adjustable spanner and the use the mallet to knock the motor through.
I also used this method. Takes a lot of force to do, but you will get it off in the end. :happy2:
-
DONE!!!!! Only problem being is i've broken the small piece that pushes in the end of the wiper motor shaft that directs the water on to the screen (only push on part) :ashamed: Is this a seperate part i can buy or do i need to look for a knackerd motor an take it off?
Thanks for all your help Guys.
-
You can buy the part as i have replaced mine as it was broken when i got the car. It was about £5 don't know the part number though. :happy2:
-
You can buy the part as i have replaced mine as it was broken when i got the car. It was about £5 don't know the part number though. :happy2:
Nice one matt!
The part is about 5mm long with the metal ball in the end to direct the water. That right????
-
Be gentle as this ETKA is new to me but I THINK the part number MAY be 3B9 955 985 A - Spray Jet
Hopefully someone else with more experience with ETKA will either confirm the number or give you the right 1 :happy2:
-
Wish I'd seen this earlier :ashamed:
There's no need to remover the arm. All you needed to do to get the handle out was to unscrew the wiper motor and rotate it through 90 degrees and you can get the handle unit out whilst still keeping the motor and wiper arm in tact.
-
Mines was a total nightmare to come off :rolleye: i ended up cutting {VERY CAREFULLY} the nut off. Everything still intact :happy2:
-
Nice one matt!
The part is about 5mm long with the metal ball in the end to direct the water. That right????
[/quote]
Yeah thats the bit a replaced.
-
Wish I'd seen this earlier :ashamed:
There's no need to remover the arm. All you needed to do to get the handle out was to unscrew the wiper motor and rotate it through 90 degrees and you can get the handle unit out whilst still keeping the motor and wiper arm in tact.
Oh well no worries. It may help someone else out on here Hurdy.
-
Mines was a total nightmare to come off :rolleye: i ended up cutting {VERY CAREFULLY} the nut off. Everything still intact :happy2:
It wasn't the nut that was the problem, that came off fine! it was actually pulling the arm off the shaft to let the motor to drop
-
Be gentle as this ETKA is new to me but I THINK the part number MAY be 3B9 955 985 A - Spray Jet
Hopefully someone else with more experience with ETKA will either confirm the number or give you the right 1 :happy2:
Your always there for me Craig!! :grin:
-
Just dewipered the rear. On my last mk5 I had a similar issue.
Purchased a wiper arm removal tool. Cost £10 just saved any hassled or risk of damage. Mines Sykes Pickavant but laser do one the same.
Search a well known auction site for "wiper tool".