MK5 Golf GTI
All Things Mk5 => Mk5 General Area => Topic started by: Jayy26 on July 24, 2015, 10:44:26 pm
-
:surprised: a few codes my mate has just pulled up hopefully someone can help and one of these is the main problem to my rad fans not working?
Car has got a decat *cough* revo said they had took this of with the map but obviously not
The relay labeled 1 is getting warm so that might help
00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
03-ABS Brakes -- Status: OK 0000
08-Auto HVAC -- Status: OK 0000
09-Cent. Elect. -- Status: Malfunction 0010
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: OK 0000
17-Instruments -- Status: OK 0000
19-CAN Gateway -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: OK 0000
46-Central Conv. -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
56-Radio -- Status: Malfunction 0010
-------------------------------------------------------------------------------
Address 01: Engine Labels: 06F-907-115-AXX.lbl
Part No SW: 1K0 907 115 HW: 1K0 907 115
Component: 2.0l R4/4V TFSI 00 0070
Revision: --H01--- Serial number: VWZ7Z0E2735184
Coding: 0403000318070060
Shop #: WSC 00015 210 70345
VCID: 63CFA3C6A21A403913D-8036
8 Faults Found:
001056 - Catalyst System; Bank 1
P0420 - 002 - Efficiency Below Threshold - MIL ON
Freeze Frame:
Fault Status: 11100010
Fault Priority: 0
Fault Frequency: 1
Reset counter: 255
Mileage: 153007 km
Time Indication: 0
Date: 2000.00.00
Time: 21:03:34
Freeze Frame:
RPM: 1530 /min
Load: 26.7 %
Speed: 41.0 km/h
Temperature: 85.0°C
Temperature: 33.0°C
Absolute Pres.: 1010.0 mbar
Voltage: 13.970 V
001670 - ECM Power Relay Control Circuit
P0686 - 002 - Short to GND - Intermittent
Freeze Frame:
Fault Status: 00100010
Fault Priority: 0
Fault Frequency: 5
Reset counter: 255
Mileage: 153319 km
Time Indication: 0
Date: 2000.00.00
Time: 16:09:09
Freeze Frame:
RPM: 0 /min
Load: 0.0 %
Speed: 0.0 km/h
Temperature: 72.0°C
Temperature: 38.0°C
Absolute Pres.: 1000.0 mbar
Voltage: 1.524 V
001672 - ECM Power Relay Load Circuit
P0688 - 004 - Open Circuit - Intermittent
Freeze Frame:
Fault Status: 00100100
Fault Priority: 0
Fault Frequency: 5
Reset counter: 255
Mileage: 153319 km
Time Indication: 0
Date: 2000.00.00
Time: 16:09:09
Freeze Frame:
RPM: 0 /min
Load: 0.0 %
Speed: 0.0 km/h
Temperature: 72.0°C
Temperature: 38.0°C
Absolute Pres.: 1000.0 mbar
Voltage: 0.381 V
009730 - Coolant Pump Control Circuit
P2602 - 002 - Short to Ground - Intermittent
Freeze Frame:
Fault Status: 00100010
Fault Priority: 0
Fault Frequency: 1
Reset counter: 255
Mileage: 153319 km
Time Indication: 0
Date: 2000.00.00
Time: 16:42:36
Freeze Frame:
RPM: 0 /min
Load: 0.0 %
Speed: 0.0 km/h
Temperature: 60.0°C
Temperature: 41.0°C
Absolute Pres.: 1000.0 mbar
Voltage: 0.000 V
000257 - Mass Air Flow Sensor (G70)
P0101 - 008 - Implausible Signal - Intermittent
Freeze Frame:
Fault Status: 00101000
Fault Priority: 0
Fault Frequency: 6
Reset counter: 255
Mileage: 153321 km
Time Indication: 0
Date: 2000.00.00
Time: 17:32:05
Freeze Frame:
RPM: 1524 /min
Load: 22.0 %
Speed: 0.0 km/h
Temperature: 81.0°C
Temperature: 35.0°C
Absolute Pres.: 1000.0 mbar
Voltage: 14.224 V
012403 - Fuel Pump Circuit
P3073 - 004 - Electrical Malfunction - Intermittent
Freeze Frame:
Fault Status: 00100100
Fault Priority: 0
Fault Frequency: 3
Reset counter: 255
Mileage: 153357 km
Time Indication: 0
Date: 2000.00.00
Time: 23:13:00
Freeze Frame:
RPM: 872 /min
Load: 18.4 %
Speed: 0.0 km/h
Temperature: 110.0°C
Temperature: 49.0°C
Absolute Pres.: 1010.0 mbar
Voltage: 13.716 V
012599 - Intake Manifold Runner Control
P3137 - 001 - Basic Setting not Completed - Intermittent
Freeze Frame:
Fault Status: 00100001
Fault Priority: 0
Fault Frequency: 1
Reset counter: 255
Mileage: 0 km
Time Indication: 0
Freeze Frame:
RPM: 140 /min
Load: 71.3 %
Speed: 0.0 km/h
Temperature: 57.0°C
Temperature: 49.0°C
Absolute Pres.: 990.0 mbar
Voltage: 8.636 V
001602 - Sensor Reference Voltage A: Circuit
P0642 - 002 - Low - Intermittent
Freeze Frame:
Fault Status: 00100010
Fault Priority: 0
Fault Frequency: 1
Reset counter: 255
Mileage: 0 km
Time Indication: 0
Freeze Frame:
RPM: 140 /min
Load: 71.3 %
Speed: 0.0 km/h
Temperature: 57.0°C
Temperature: 49.0°C
Absolute Pres.: 990.0 mbar
Voltage: 7.239 V
Address 46: Central Conv. Labels: 1K0-959-433-MIN.clb
Part No: 1K0 959 433 AJ
Component: KSG 0401
Coding: 19C802087F2D8405485AC69010CC
Shop #: WSC 00139 210 82586
VCID: 78F5E4AA0B9CB3E156F-802D
Subsystem 1 - Component: Sounder No Answer
Subsystem 2 - Part No: 1K0 907 719 C
Component: Neigungssensor 005 0003
Subsystem 3 - Part No: 1K0 951 177 A
Component: Innenraumueberw.005 0202
1 Fault Found:
01134 - Alarm Horn (H12)
004 - No Signal/Communication
any help would be great cheers
-
bump
-
anyone?
-
Might not be much help but have you looked the codes up on the Ross Tech website for a few reasons as to what the issue could be?
-
Cheers bud ive had a quick glance but i think its going to take me a while to troubleshoot ;/
-
P0420 is the rear O2 sensor...just had that code and replacing the rear O2 fixed it. The rest you can sort out here: http://wiki.ross-tech.com/wiki/index.php/Main_Page
Enter the codes into "Search"
-
The alarm horn will be either the siren in the drivers side front arch as battieres corrode or the switch on your drivers side door pillar easy fix for your diy
Let me know if you want any help with this
-
P0420 is the rear O2 sensor...just had that code and replacing the rear O2 fixed it. The rest you can sort out here: http://wiki.ross-tech.com/wiki/index.php/Main_Page
Enter the codes into "Search"
yeh its because i have a decat,have you heard of them blank pieces of metal that apparently bypass this?
The alarm horn will be either the siren in the drivers side front arch as battieres corrode or the switch on your drivers side door pillar easy fix for your diy
Let me know if you want any help with this
so does the alarm use a different battery?which switch bud?
-
alarm.
The siren has built batteries so the alarm works if you ever get a flat battery but they are known To corrode over time and cause the alarm to fault and either not working or make the alarm go off.
Its in the drivers front wing in a metal box bolted to the chasiss
Also the switch it next to the drivers seat on the b pillar it turns the sensors off if you ever wanna leave dogs in the car or sensors for towing
Cheers
Alex
-
Any help on these would be great i dont even know where to start...thanks
001670 - ECM Power Relay Control Circuit
P0686 - 002 - Short to GND - Intermittent
Possible Causes
Power Supply Relay for Engine Control Module (J271) faulty
Wiring between Engine Control Module (J220) and Power Supply Relay for Engine Control Module (J271) faulty
Possible Solutions
Check/Replace Power Supply Relay for Engine Control Module (J271)
Check Wiring between Engine Control Module (J220) and Power Supply Relay for Engine Control Module (J271)
Check/Replace Engine Control Module (J220)
001672 - ECM Power Relay Load Circuit
P0688 - 004 - Open Circuit - Intermittent
Possible Symptoms
Engine Coolant Fan running at full Speed while Ignition is OFF and Engine is COLD (could lead to discharged Battery)
Possible Causes
Fuse(s) faulty
Power Supply Relay for Engine Control Module (J271) faulty
Terminal 87 faulty/hanging
Wiring between Engine Control Module (J220) and Power Supply Relay for Engine Control Module (J271) faulty
Possible Solutions
Check/Replace Power Supply Relay for Engine Control Module (J271)
Check Wiring between Engine Control Module (J220) and Power Supply Relay for Engine Control Module (J271)
Check/Replace Engine Control Module (J220)
009730 - Coolant Pump Control Circuit
P2602 - 002 - Short to Ground – Intermittent
Cannot find this in ross tech but it seems to come with the faults above ^^
000257 - Mass Air Flow Sensor (G70)
P0101 - 008 - Implausible Signal – Intermittent
Possible Symptoms
Loss of Power
Erratic Idle
Possible Causes
Mass Air Flow Sensor (G70) faulty
Air Leak(s) after Mass Air Flow Sensor (G70)
Excessive restrictions in the Intake/Exhaust System
Dirty air filter, clogged snow screen, clogged CAT
Ground Spots corroded or Paint Residue
Wiring and/or Connections from/to Mass Air Flow Sensor (G70) faulty
Possible Solutions
Check Intake Air Filter
Check Mass Air Flow Sensor (G70)
Check Ground Spots
Check Wiring and/or Connections from/to Mass Air Flow Sensor (G70)
012403 - Fuel Pump Circuit
P3073 - 004 - Electrical Malfunction – Intermittent
Possible Symptoms
Malfunction Indicator Light (MIL) ON
No start or performance problem(s)
Possible Causes
Wiring and/or Connector(s) from/to Transfer Fuel Pump (G6) -or- Fuel Pump (FP) Control Module (J538) faulty.
Transfer Fuel Pump (G6) faulty. See Special Notes
Fuel Pump (FP) Control Module (J538) faulty.
Possible Solutions
Check Fuse(s), Wiring and/or Connector(s).
Check/Replace Transfer Fuel Pump (G6). See Special Notes
Check/Replace Fuel Pump (FP) Control Module (J538).
Special Notes
When found in the M.Y. 2006 - 2007 NAR BPY 2.0T FSI engine see:
TSB 01-08-06 -or- TPI 2017131 which mentions "updated" electric/transfer (in tank) fuel pumps.
012599 - Intake Manifold Runner Control
P3137 - 001 - Basic Setting not Completed – Intermittent
Possible Causes
Intake Manifold Runner Control Basic Setting not performed
Possible Solutions
Perform Intake Manifold Runner Control Basic Setting
Special Notes
When found in Engine: 2.0l TFSI
Perform Basic Setting.
Check TPL 2016420 (RoW)
Check Engine Control Module Software Version, if necessary perform Update.
Replace Intake Manifold Runner (V157) with updated part.
001602 - Sensor Reference Voltage A: Circuit
P0642 - 002 - Low - Intermittent
Possible Causes
Control Module and/or Sensor Power Supply faulty
Possible Solutions
Check Control Module and/or Sensor Power Supply
Special Notes
When found in Engine: 2.0l TFSI
Check Wiring from/to the following Components and Components themselves:
Manifold Pressure / Boost Sensor (G31)
Intake Manifold Tuning Valve Position Sensor (G336)
Low Pressure Fuel Sensor (G410)
Check TPL 2016420 (RoW)
Check Engine Control Module Software Version, if necessary perform Update.
Replace Intake Manifold Runner (V157) with updated part.
Check TSB 01-08-12 or 2018402
Check Engine Control Module Software Version, if necessary perform Update.
Replace Intake Manifold Runner (V157) with updated part.
Additional information may be found by searching RVU 24M2 / O3 (Exp. date November 30, 2011) or calling the VW dealer and checking the VIN.
Just found the last fault on this page and looks like it could just be down to that?
-
anyone ever changed there ECU ?
-
P0420 is the rear O2 sensor...just had that code and replacing the rear O2 fixed it. The rest you can sort out here: http://wiki.ross-tech.com/wiki/index.php/Main_Page
Enter the codes into "Search"
yeh its because i have a decat,have you heard of them blank pieces of metal that apparently bypass this?
You mean the O2 spacer? Yes, it helps a majority of those whom have tried it. I think it is best to replace or you can clean, only cleaning is said to only last a short time and why I think replacing is best. I just got the code again and need to replace the second O2 now.
On your multiple codes...remember to address the first codes to pop up. Look at the timeline for the codes, address the first to pop up because one code can lead to others. Fix one, clear the codes, and address further should other codes appear again continuing to address by timeline that they appear.
-
thats the one haha well i have a decat so cleaning wouldnt help would it?
right got you..well apparently my mates dads said it the control main relay? :/