All Things Mk5 > How to Guides / Troubleshooting
Heated seats
ollie288:
Hi I fitted heated leather seats to my 1.6 fsi se golf a while a go. I bought this:
http://cgi.ebay.de/ws/eBayISAPI.dll?ViewItem&item=350213500745&ssPageName=ADME:X:RTQ:DE:1123
Same as my heater controls except they have the heated seat controller on the sides.
I need to get one of these:
http://www.kufatec.de/shop/product_info.php/info/p680_Kabelsatz-Sitzheizung-Golf-5-V.html
I am unsure of which selections I need. I contacted them but they were not much help. I need to now if mine is heating, climatic. I also need the lower back electrical adjustment.
Does anyone know what to select?
Cheers :happy2:
ollie288:
Purchased the harness and t arrived today. The only problem is this is what they have gave me for instructions. Could one of you clever people covert this to something I understand! :stupid: :signLOL:
Here they are:
Manual wiring heated seats Golf V until October 2006
Please disconnect the battery before starting installation.
Please wire the loom starting from the seats to the following connections:
Wire configuration:
Steady plus - Fuse box
Ignition plus - Fuse box
Double crimp - Control unit central electric Connector C – PIN 1
Wire with 2 looms - Climate control unit – 20-pole Connector
Driver site - PIN 10
Passenger site - PIN 11
Single loom - Climate control unit – 20-pole Connector – Pin 12
Opposite to ignition plus, Fuse box SC7
Ring terminal - Ground A-Column, driver site
After installation you need to code the control unit for central electric (address 09) to heated seats.
Where does it all go!!!?
mortygttdi:
Steady plus - Fuse box Constant feed
Ignition plus - Fuse box Ignition feed
Double crimp - Control unit central electric Connector C – PIN 1 This is the main control board under the dash fuse box
Wire with 2 looms - Climate control unit – 20-pole Connector This is behind the climatic control panel under the headunit
Driver site - PIN 10 Same as abov
Passenger site - PIN 11 Same as above
Single loom - Climate control unit – 20-pole Connector – Pin 12 Same as above
Opposite to ignition plus, Fuse box SC7 Wire goes to the Fuse box socket 7
Ring terminal - Ground A-Column, driver site Bottom of A pillar ground position
After installation you need to code the control unit for central electric (address 09) to heated seats. Code Cent Elec for heated seats
Sounds easy but prob take an hour or so.
Darren
mortygttdi:
Kufatec should have supplied you with a wiring colour diagram??? if not you may have to go onto there website and download it, on your emails you will have a customer number and id number these will be your account details on kufatec so you can download your specific instructions.
Darren
mk5rabbit:
Bringing this back up to help out people in the future...
Just accomplished the heated seats today in my rabbit... THE ONLY PROBLEM WITH THE INSTRUCTIONS is that where they tell you to put the "Driver site - Pin 10, Passenger site - Pin 11, and Single loom - Pin 12"..... Follow the original instructions ONLY IF you have Climatronic Climate Control. a.k.a. the "Digital" one. I installed this wiring harness to a "Climatic Climate Control", and after countless amounts of times of trial and error i finally figured it out. This is how it goes...
IF you have one of the following, go by these directions:
Climatronic: Single loom - Climate control unit 20-pole connector Pin 12
Driver Site - Pin 10
Passenger Site - Pin 11
Climatic: Single loom - Climate control unit 20-pole connector Pin 15
Driver Site - Pin 13
Passenger Site - Pin 12
If done correctly, follow the "Driver site" wire from the control unit you have just plugged it into, all the way down to the connector where the harness meets the seat. Hook a voltmeter to this wire at the connector. The higher you move the heated seat knob, the higher this voltage will get, only hitting about 8 volts at maximum....
Navigation
[0] Message Index
[#] Next page
Go to full version