MK5 Golf GTI
All Things Mk5 => Modifications & Technical Area => Cosmetic/Interior Modifications => Topic started by: tkboyle on July 11, 2012, 06:42:54 pm
-
Hi,
Just had cruise control fitted and coded to a MY07 ED30.
It appears to have been coded and is registering commands as seen in vcds although it's not activating on the road.
The car has MFSW and Highline and is a manual.
Would like if possible for someone to post the coding if they have the same spec.
The stalk is the newer Mk6 one (1K0 953 513 G)
cheers
-
Did you code both the steering controller and the engine?
-
Did you code both the steering controller and the engine?
Yep it's been coded.
Steering Wheel Module
Address 16: Steering wheel Labels: 1K0-953-549-MY8.lbl
Control Module Part Number: 1K0 953 549 BD HW: 1K0 953 549 BD
Component and/or Version: J0527 638 0070
Software Coding: 0002022
Work Shop Code: WSC 12345 123 12345
Additional Info: XXXXXXXXXXX E0221 002 0010
Additional Info: Geraet 12345
VCID: 75E5E5E76701
No fault code found.
Engine Module
040300031807 01 60
I'm not sure if the values represented in the steering module are correct.
-
Does your steering controller support cruise??
-
did you check that the plug on the back of the control module had the diagnostic wire?
pin 13?
(https://www.mk5golfgti.co.uk/forum/proxy.php?request=http%3A%2F%2Fdaz.co%2Fmedia%2FCaddy%2Fcruise_control%2Fpin13.jpg&hash=9ba13f53e1d2f0facd4a402c2d07d59f92c4178b)
-
Does your steering controller support cruise??
Yes it does its the highline variant.
Control Module Part Number Slip Ring Software Level Variant Steering Angle Sensor LIN Version Notes
1K0-953-549-BD Type 2 SW 0070 Highline Yes 1.3 #2#2: Manual Transmission only, does NOT support Ignition Key Lock.
-
did you check that the plug on the back of the control module had the diagnostic wire?
pin 13?
(https://www.mk5golfgti.co.uk/forum/proxy.php?request=http%3A%2F%2Fdaz.co%2Fmedia%2FCaddy%2Fcruise_control%2Fpin13.jpg&hash=9ba13f53e1d2f0facd4a402c2d07d59f92c4178b)
Is this the black and white wire? if so its there already.
-
Do you have any fault codes?
Was the stalk new?
-
Do you have any fault codes?
Was the stalk new?
No faults. The stalk is brand new from VW.
-
Think I might have found my answer.
Just a Note for others
ANY controller with 638 0070 HW and SW will not allow cruise to be fitted
-
Hi
as I posted earlier any controller with 638 0070 will not work
all other version are ok
You will need to change it any of the following
BK BP BD AK AQ CH
-
Oh. I have a BD
-
Oh. I have a BD
yes you have a BD with the wrong HW / SW
there are other BD controllers with different HW / SW just make sure whatever you buy doesn't have 638 0070 on the label
-
Can you supply these Eddie?
If so can you PM me.
-
Presuming you have sat at a steady speed over 30mph to activate. Controls do nothing stationary, Sounds stupid but a friend was expecting the light to come on once fiited/coded.
-
I did manage to get to 88mph. Only then did it switched on. Once activated I then found myself driving in 1955.
-
Oh. I have a BD
yes you have a BD with the wrong HW / SW
there are other BD controllers with different HW / SW just make sure whatever you buy doesn't have 638 0070 on the label
where on the label will this code be? is it part of the part number? pic would be awesome.
will just be helpful for the future when asking friends to check there controller to see if its cruise compatible.
-
Would one of these go straight on an 08 car with just the coding needing doing?.
-
Depends what Steering Wheel Controller and slip ring You have Mate.
-
Depends what Steering Wheel Controller and slip ring You have Mate.
..........i guess?.Just wondered if being a later car it would have the correct slip ring?.
-
Depends what Steering Wheel Controller and slip ring You have Mate.
..........i guess?.Just wondered if being a later car it would have the correct slip ring?.
slip ring depends on the control module.