All Things Mk5 > How to Guides / Troubleshooting
Problem with G85 / clock spring after MFSW retrofit
supercati:
EDIT: Problem was solved. You can read through the thread.
Hello there.
This past weekend I had Tempomat + MFSW installed on my Golf mk5 (2007 1.4 TSI 170).
Tempomat works great, Multifunction steering wheel too (horn, buttons, ilumination)... but, I cannot erase G85 errors. I believe this is also steering angle sensor / clock spring after some Google.
I've tried to do the basic setup, but it's impossible since the "Angle" value doesn't move from 0.00º (when I check in 03 - Brakes and Channel 004). Maybe it is broken? It was always working fine before removing steering wheel...
I tried this: http://wiki.ross-tech.com/wiki/index.php/VW_Golf_(1K)_Brake_Electronics_(MK60) but didn't work either.
SMLS is ref. CH, clock spring ref. 1K0959653C.
Any help will be really apreciated!
supercati:
I replaced the G85 today for a brand new one... same result!! I cannot understand anything now.
What I am doing wrong? With VagCom still the same, cannot read any angle, I thought it was because of the G85 being defective but may be not?
r5gtt:
Is this what you did?
Basic Setting
Sensor for Steering Angle (G85)
Prerequisites:
Start the vehicle.
Turn the steering wheel one turn to the right and one turn to the left.
Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
Ensure that the steering wheel is not moved again.
Keep the engine running and do not switch off the ignition.
System voltage at least 12.0 V.
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 °.
[Done, Go Back]
[Coding-II - 11]
OR (if Coding-II is not available)
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
[Close Controller, Go Back - 06]
Note: After successful basic setting, the Steering Limit Stop needs to be adapted too.
v4rley:
Go into control module 44 steering assistance
[44 - Steering Assist]
[Coding-II - 11] or if that function is not available then use [Sec.Access - 16] instead
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 1 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 007
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 °.
[Done, Go Back]
[Close Controller, Go Back - 06]
supercati:
R5gtt, I did that, but didn't work out. When I go to channel 60 the angle doesn't move from 0.00°, and if I try to do basic setting it says error.
--- Quote from: v4rley on June 08, 2016, 09:45:22 pm ---Go into control module 44 steering assistance
[44 - Steering Assist]
[Coding-II - 11] or if that function is not available then use [Sec.Access - 16] instead
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 1 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 007
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 °.
[Done, Go Back]
[Close Controller, Go Back - 06]
--- End quote ---
I haven't done this, so I'll give it a try later! And I'll post the result.
The only thing I don't understand at all:
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 1 should say "OK".
What I am supposed to do after activating Basic Setting? The car will do it itself, or I need to drive, or turn left/right?
Thanks is advance :)
Navigation
[0] Message Index
[#] Next page
Go to full version